經濟部標準檢驗局個人防護用具實施商品驗證登錄品目明細表

Proposal for implementing mandatory commodity inspection of
secondary lithium cells and batteries, secondary lithium mobile power
bank and battery charger for computer, communication and consumer
electronics
By the Bureau of Standards, Metrology and Inspection (BSMI), Ministry of Economic Affairs

Background:
Along with the development and popularization of science and technology, electronic products for computer, communication and consumer electronics are the necessary equipments in modern life, The secondary lithium cells and batteries, secondary lithium mobile power bank and battery chargers are ready to provide power for products of computer, communication and consumer electronics. In order to enhance the consumers protection, the BSMI intends to mandatory inspection requirements for secondary lithium cells and batteries, secondary lithium mobile power bank and battery charger for computer, communication and consumer electronics. The conformity assessment procedure for all such products will be under the Registration of Product Certification Proposed date of implementation:
‧March 1, 2014

Table of secondary lithium cells and batteries, secondary lithium mobile power bank and battery
charger for computer, communication and consumer electronics (HS/CCC codes) covered and their
applicable inspection standards:
C.C.C.Code(the
Description of
first 6 digits are
Inspection Standards
Inspection scheme
the same as HS
Remarks 1.CNS 15364 (2010) Secondary cells and batteries containing alkaline or other non-acid electrolytes - Safety requirements for portable sealed secondary cells, and for batteries made from them, for use in portable applications. Information technology equipment - Safety - Part 1: General Audio, video and similar electronic apparatus - Safety 4.CNS 13438 (2006)Information technology equipment - Radio disturbance characteristics - Limits and methods of measurement. The conformity assessment procedures for the inspection schemes are as follows:
Registration of Product Certification (RPC) Scheme(Module II+ III)
Under this procedure, domestic manufacturers or importers must have their products type-tested in advance (Module II) before applying for registration of their products. Manufacturers or importers will also be required to ensure by declaration that all products made at their manufacturing facilities or imported are in conformity with the prototypes submitted for type test at Module II stage, and the declaration procedure is called Module III (conformity-to-type declaration). The conformity-to-type declaration shall be drawn up by the manufacturer or the authorized local representative, declaring that the products mass-produced will comply with the prototype as described in the type-test report. Products will be allowed to use the Commodity Inspection Mark with the letter “R” and the identification number given by the BSMI, after they are certified and registered with the BSMI. These products can then pass through customs directly without any further inspection if not be sampled by RPC border check procedure. The application fee and annual fee for RPC are both NT$5,000(about US$170) for each certification, and the RPC certifications are valid for three years. If there are any serial products, the extra NT$3,000(about US$102) of application fee is needed for every application in each certification. Locations to apply for Type Testing:
‧The BSMI or BSMI-designated testing laboratories. Locations to apply for Registration of Product Certification:
Time required for Registration of Product Certification:
‧Fifteen working days. (This period does not include the time for corrective actions by the
applicant due to deficiencies in the documents or samples; another seven working days may
be required if additional tests are required)
Related requirements:
1. Since 2014 March 1, the above-mentioned secondary lithium cells and batteries, secondary lithium mobile power bank and battery charger for computer, communication and consumer electronics will be implemented mandatory commodity inspection. The available inspection procedure is the Registration of Product Certification (RPC) Scheme. When the BSMI completes the review procedure and approves the application, a certification will be issued and valid for 3 years starting from the issue date. 2. The inspection standards shall be the latest version of standards as of the date this public notice to be adopted. When the applicable standard is revised or amended, the date of applying the revised or amended standard shall be decided and announced by the BSMI. the products covered in this notice, the technical documents required for type testing shall the products covered in this notice have combined functions or multi-functions themselves, they shall comply with other relevant standards. If the products are equipped with some accessories which are implemented mandatory inspection, those accessories shall comply with

Source: http://www.hntbt.org.cn:8080/html/mcw/upload/attach/2013/08/14/20130814095402889.pdf